KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Subaru Select Monitor

COMMUNICATION FOR INITIALIZING IMPOSSIBLE

DIAGNOSIS:

NOTE:

Confirm that the LAN system is working properly before the diagnosis.

Subaru Select Monitor communication line is open or shorted.

TROUBLE SYMPTOM:

Not communicable with Subaru Select Monitor.

WIRING DIAGRAM:

STEPCHECKYESNO

1.CHECK IGNITION SWITCH.

Is the ignition switch ON?

Turn the ignition switch to ON, and select Integ. unit mode using Subaru Select Monitor.

2.CHECK BATTERY.

1) Turn the ignition switch to OFF.

2) Measure the battery voltage.

Is the voltage 11 V or more?

Charge or replace the battery.

3.CHECK BATTERY TERMINAL.

Is there poor contact at battery terminal?

Replace the battery, or clean and tighten the terminals.

4.CHECK COMMUNICATION OF SUBARU SELECT MONITOR.

1) Turn the ignition switch to ON.

2) Using the Subaru Select Monitor, check whether communication to other systems can be executed normally.

Is the system name displayed?

5.CHECK COMMUNICATION OF SUBARU SELECT MONITOR.

1) Turn the ignition switch to OFF.

2) Disconnect the body integrated unit connector.

3) Turn the ignition switch to ON.

4) Check whether communication to other systems can be executed normally.

Is the system name displayed?

6.CHECK HARNESS CONNECTOR BETWEEN EACH CONTROL MODULE AND SUBARU SELECT MONITOR.

1) Turn the ignition switch to ON.

2) Disconnect the body integrated unit connector.

3) Measure the resistance between data link connector and chassis ground.

Connector & terminal

(B40) No. 7 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair the harness and connector between each control module and Subaru Select Monitor.

7.CHECK OUTPUT SIGNAL TO BODY INTEGRATED UNIT.

1) Turn the ignition switch to ON.

2) Measure the voltage between body integrated unit and chassis ground.

Connector & terminal

(B40) No. 7 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the harness and connector between each control module and Subaru Select Monitor.

8.CHECK HARNESS CONNECTOR BETWEEN BODY INTEGRATED UNIT AND DATA LINK CONNECTOR.

Measure the resistance between body integrated unit and data link connector.

Connector & terminal

(B40) No. 7 — (B280) No. 20:

Is the resistance less than 1 Ω?

Repair the harness and connector between body integrated unit and Subaru Select Monitor.

9.CHECK INSTALLATION OF BODY INTEGRATED UNIT CONNECTOR.

Turn the ignition switch to OFF.

Is the body integrated unit connector inserted into body integrated unit until the clamp locks onto it?

Insert the body integrated unit connector into body integrated unit.

10.CHECK POWER SUPPLY CIRCUIT.

1) Turn the ignition switch to ON (engine OFF).

2) Measure the ignition voltage between body integrated unit connector and chassis ground.

Connector & terminal

(B280) No. 1 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Repair the open circuit of harness between body integrated unit and battery.

11.CHECK HARNESS CONNECTOR BETWEEN BODY INTEGRATED UNIT AND CHASSIS GROUND.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from body integrated unit.

3) Measure the resistance of harness between the body integrated unit and chassis ground.

Connector & terminal

(B280) No. 20 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair the poor contact of harness between body integrated unit and ground.

12.CHECK POOR CONTACT OF CONNECTOR.

Is there poor contact of the control unit ground and the Subaru Select Monitor?

Replace the body integrated unit.

Repair the poor contact of connector.

CAUTION:

Model with immobilizer will require registration work when the body integrated unit, collation CM, steering lock CM, ID code box, ECM, or combination meter are replaced. For the registration procedures, refer to the “PC application help for Subaru Select Monitor”.